• Home
  • Precautions for the appearance of plastic molds

Precautions for the appearance of plastic molds

Precautions for the appearance of plastic molds
 
1: The content of the nameplate should be printed with the mold number, mold weight (KG), and mold size (mm). The characters are all marked with 1/8 inch code, and the characters are clear and neatly arranged.
 
2: The nameplate should be fixed on the mold leg near the rear template and the reference corner (15mm away from both sides), fixed with four rivets, fixed reliably, and not easy to peel off.
 
3; The cooling water nozzle should use a plastic block to insert the water nozzle, ¢10 tube, the specification can be G1/8″, G1/4″, G3/8″. If there are special requirements in the contract, please follow the contract.
 
4: The cooling water nozzle should extend out of the aluminum cnc parts surface, and the head of the water nozzle recessed into the outer surface should not exceed 3mm.
 
5: The diameter of the cooling water nozzle avoidance hole should be ¢25, ¢30, ¢35mm three specifications, the outer edge of the hole has a chamfer, the chamfer is greater than 1.5×45, and the chamfer is the same.
 
6: The cooling water nozzle must have an entry and exit mark, the inlet water is IN, the outlet water is OUT, and the sequence number is added after IN and OUT, such as IN1 and OUT1.

7: Mark English characters and numbers should be capitalized (5/6″), the location is 10mm directly below the tap, the handwriting is clear, beautiful, neat, and evenly spaced.
 
8: The inlet and outlet nozzles and the inlet and outlet nozzles should be the same as the cooling water nozzles, and add G (gas) and O (oil) with a blank character before IN and OUT.
 
9: There are water nozzles on the upper and lower sides of the mold installation direction, which should be built-in, and open the diversion groove or have a support column under it for protection.
 

10: The oil nozzle or water nozzle that cannot be built-in should be protected by a support column.
 
11: Machining uhmw mold base must have a reference angle symbol for each template, capitalized English DATUM, the word height is 5/16″, the location is 10mm away from the side, the writing is clear, beautiful, neat, and evenly spaced.
 
12: Each template must have a part number. The number is 10mm from the bottom directly below the reference angle symbol, and the requirements are the same as No. 11.
 
13: Mold accessories should affect the lifting and storage of the mold. For example, there should be support legs to protect the oil tank, water nozzle, and pre-reset mechanism that leak underneath during installation.
 
14: To install the support leg, use screws to pass through the support leg and fix it on the mold base, or to fasten the excessively long support leg to the mold base by turning external threads.
 
15: Machining uhmw plastic mold ejection hole must meet the specified injection molding machine, except for small molds, in principle, one center cannot be used for ejection (when the length or width of the mold is greater than 500mm), the ejection hole diameter should be larger than the top The rod is 5-10mm larger.
 
16: The positioning ring should be reliably fixed (usually three M6 or M8 hexagon socket screws), the diameter is generally ¢100 or ¢150mm, 10mm higher than the top plate. If there are special requirements in the contract, the same shall apply.
 
17: The mounting hole of the positioning ring must be a counterbore, and it is not allowed to be directly attached to the top surface of the mold base.
 
18: When a custom cnc aluminum mold weighing more than 8000KG is installed on the injection molding machine, the screw must be pressed by perforation, and the plate must not be pressed separately. If the equipment uses hydraulic locking molds, screw perforations must also be added to prevent the failure of the hydraulic mechanism.
 
19: The sprue bushing ball R is larger than the nozzle ball R of the injection molding machine.
 
20: The inlet diameter of the sprue bushing should be larger than the diameter of the nozzle injection port.
 
21: The overall dimensions of the mold must conform to the specified injection molding machine.
 
22: The surface of the mold base must have pits, rust marks, unnecessary rings, water, gas, oil holes, etc., and other defects that affect the appearance.
 
23: Each plate of the mold base must have a chamfer greater than 1.5mm.
 
24: The mold should be convenient for hoisting and transportation, and the mold parts must not be disassembled during hoisting (except for the oil cylinder, which needs to be packaged separately). The lifting ring interferes with the faucet, oil cylinder, pre-reset rod, etc., and the position of the lifting ring hole can be changed.
 
25: Each mold component weighing more than 10KG must have a suitable lifting eye hole. If not, corresponding measures must be taken to ensure that the component is easy to disassemble and install. The size of the ring and the position of the ring hole are designed according to the relevant enterprise standards.
 
26: If ejector mechanisms such as ejector rods and ejector blocks interfere with sliders, etc., there must be a forced pre-reset mechanism, and the top plate has a reset travel switch.
 
27: The cylinder core and ejection must be controlled by a travel switch, and the installation is reliable.
 
28: The mold oil separator should be fixed and reliable. The oil pipe connecting the oil separator and the oil cylinder should use a rubber tube, and the joint should use standard parts.
 
29: There must be trash nails on the thimble plate. The clamping device should be installed reliably, with positioning pins, symmetrical installation, no less than 4 (small molds can be 2).
 
30: If the injection molding machine adopts an extended nozzle, there should be enough space inside the positioning ring to ensure that the extended nozzle with heating ring of the standard injection molding machine can extend in.
 
31: All inclined tops can be removed from a hole that passes through the bottom plate and the thimble bottom plate and whose angle is the same as the inclined top angle.
 
32: The bottom surface of the screw mounting hole must be flat. Screws above M12 (including M12) must be (12.9 grade).

Post a Comment

Note: Only a member of this blog may post a comment.

Recent News

[latest][5][recentright]

PTJ RFQ

What Is PTJ?
PTJ adopts flexible manufacturing methods to help our customers to control the product cost but best quality guranteed. Some frequently used machining processes include CNC milling, CNC turning, precision grinding, EDM machining, laser cutting, welding, CNC punching, sheet metal stamping, profile extrusion, die casting, forging, and more. Most of the custom precision cnc machining china parts and plastic machining components we made are related to automation machines, robotics, medical devices, fiber optics, aerospace/aircraft, test and measurement, sensors, telecom components, scientific devices, audio equipments, bicycles, boats, camera, cars, drones, electronic enclosures, front panels, furniture and architecture hardware, lighting, motorcycles, scooters, utv, jeeps, trucks, sports equipments, machinery, music instruments, and so on.
For Surface Finishes
Thanks to our mature supplier management and continuously experience accumulation. Now we have very stable surface finish suppliers to assist us to do different surface finishes with stable and excellent quality. Some Frequently used surface finishes are Anodizing, Oxide, Nickel Plating, Chrome Plating, Gold / Silver Plating, Powder Coating, Zinc Plating, PVD Coating, Passivation, Heat Treatment, Electrochemical machining, Brushing, Polishing, Sandblasting, etc.
General Tolerance of Equipments
1. CNC Milling tolerance: +/-0.01mm
2. CNC turning tolerance: +/-0.01mm
3. Precision grinding tolerance: +/-0.005mm
4. EDM machining tolerance: +/-0.005mm
How to Control Quality?
1. Inspection by machinist himself who is responsible for a specific part machining.
2. First article part inspection by QA.
3. IPQC patrol inspection during production.
4. PQC inspection before shipping according to ISO9001 sampling inspection standard for large quantity production. And for small quantity, 100% full inspection.
5. Material Certificates and outgoing inspection reports could be provided.
Our CNC machine and swiss machining shop sets full and advanced inspection instruments such as CMM, projector, height instrument, industrial microscope, micrometer, calipers, thread gauges, pin gauges, block gauges, etc. so as to inspect all details on drawings and confirm quality is good and issue the ourgoing reports accordingly.
How to Start Working with Our Company?
1) Sending detailed RFQ with 2D and 3D drawings to through email to info@pintejin.com. General drawing formats like PDF/ STEP/IGES/X_T etc are accepted.
2) We check and confirm about materials, surface finish and quantiy, and evaluate. If any question, our sales engineer would double check with customers until everything is clear. We will quote accordingly if we are ok to make the parts with best quality. If no question and everything is clear, we send quotation with best prices within 24 hours. Our sales engineer team is online for 7/24 for offering customers the best cnc machining services.
3) We recommend to start from few pcs prototypes for approval at the beginning. If nothing wrong after customer’s test and approval, then we proceed to volume cnc manufacturing.
Some Tips for Customers
a. We accept Paypal payment of small amount payment for samples or small batch orders for building mutual trust at the beginning. General payment terms is 30% by wire transfer, and balance before shipping.
b. Delivery time for few pcs samples are generally 5 to 7 days, and 15 to 25 days for volume production. If the order quantity was too big, we would check and confirm delivery time sepertely.
c. Our company has concrete promise to all customers that if any quality problem caused by our factory, we would remake all parts for free or send money back.
Safe Packing Methods to Prevent Goods from Damage during Transportation
Due to long distance transportation to overseas countries, safe and strong packing is very important to gurantee the parts to be in good conditions when arriving at customer’s hand. We choose different packing materials according to different parts and quantity. Some commonly used packing materials are pp/bubble bag, oil paper, foam, blister tray, 5 layer carton, wood box, etc. See below some packing pictures.